How To Install Crown Molding On Rta Cabinets

I f you're looking for a worthwhile DIY project while you lot're staying at abode and practicing social distancing due to COVID-19, why not try installing (or fixing) some crown molding on your kitchen cabinets?

This project is moderate-level in difficulty (you lot should be comfortable having to brand precise cuts using a power miter saw), and is moderate-level in cost (typically $100 - $ 3 00 for the boilerplate U.S. kitchen). However, the add-on of sharp-looking crown molding tin can have a major touch in the overall look and perceived value of your kitchen.

I f you desire your kitchen to look finished, sophisticated, and truly high-stop, then tightly fitted crown molding for your kitchen cabinets is that perfect last touch.

Here are the tools and materials you will need for this projection:

• Pneumatic Smash Gun (Brad Nailer with i ¼-in. Brads)

• 1X4 Wood Blocks (you'll need ii for each uniquely sized bending of your cabinetry)

Now , follow this step - past - stride guide:

1. Remove or Purchase

If your kitchen cabinets already have some type of crown molding installed (perhaps with a not-so-tightly fitted installation that now requires fixing), your first step will exist to remove that existing crown molding. The skilful news is, yous can probably re-use that existing molding withsome additional cuts for a better installation.

To remove whatever existing crown molding, use your flat pry bar and hammer.

If you lot're starting from scratch, you'll need to get enough of your desired crown molding for your kitchen.

2. Measure

The central to achieving tightly fitted crown molding is to become the measurements correct.

Especially if your crown molding needs to come up together at angles that are non 45 degrees, you need to be sure your crown molding measurements will match the kitchen cabinets you have. If y'all take a corner cabinet that create southward shallower angles with the remainder of your cabinetry, that's a good place to start.

To begin the measuring process, place your 2 1X4's against the ceiling then that they overlap at the cabinet corner, and draw a line where the board due south see .

You lot can use a combination square to brand a line across ane lath that connects the inside and exterior corners.

To decide the necessary length for your crown molding, measure out across your cabinets from one inside corner to the next.

Yous may demand to repeat this process if there are variations in the different bending measurements for your cabinets.

3. Cut

Now that yous have your measurements, information technology's time to use your miter saw.

Place the 1X4's on the saw table stacked ane on peak the other, and accommodate the angle of your saw blade to cut along the pencil line.

Now, you lot tin use the 1X4 blocks every bit guides to set your miter bending.

Cutting the left-side miter of your crown molding, measure out to the necessary length, then use your other cake to set the angle and then yous tin cut the right-side miter.

Echo this procedure for all t he crown molding y'all need.

4. Install

Employ yous r carpenter's glue to securely identify the crown molding confronting the cabinet and flush tight with the ceiling. And so use your nail gun to secure the first piece in place.

Earlier installing the next piece of crown molding, be sure to apply glue to the cut edge of the molding and fit it in place with your first piece. Hold it securely and nail it in place.

And so echo this process for the residual of your crown molding.

5. Paint / Stain

You now should have your crown molding fit tightly and in identify.

Of course, the final touch to ensure a professional wait is to smooth the surface and use a fresh coat of pigment.

You tin apply some drywall hole patch to fill in any gaps and cover up the nails. And so utilize 2 coats of paint and then that the molding volition complement the finish of your cabinet.

If your cabinets use a wood stain , it's recommended that y'all obtain a few wood stain sample s and examination them out on some extra molding to ensure y'all get a stain color that will complement your cabinets.

For more information on kitchen cabinet pattern, call our squad of experts at RTA Wood Cabinets at: 800-788-7575.

---

Back to RTA Woods Cabinets

Source: https://rtawoodcabinets.com/blogs/rta-woodcabinets-blog/your-step-by-step-guide-to-installing-tightly-fitted-crown-molding-on-your-kitchen-cabinets

Posted by: sterlingthwithis.blogspot.com

Share this post